Shower Repairs in Sydney

Dripping shower heads, worn mixers, weak pressure and leaking shower recesses, fixed by licensed plumbers for a fixed price you approve first.

$0 CALLOUT FEE IN BUSINESS HOURS | FREE QUOTES | SAME DAY SERVICE

Google

Overall Rating

4.9

Five stars

(2,800+)

Brightest & Best Business Awards: Winner 2019, Winner 2024, Winner 2025, People's Choice 2025, Finalist 2023

NOW SERVICING NORTH SYDNEY

  • 35+ Years of Combined Experience
  • Yes, a Real Plumber Reads These Messages Too
  • The Kettle Is Always On at Head Office
  • $0 Call Out Fees
  • Every Job Photographed, Every Price Upfront
  • We Answer the Phone. Revolutionary, We Know.
  • Trusted by 15,000+ Sydney Families
  • No Call Centres. You Get a Human in Sydney
  • Your Neighbours Probably Have Our Fridge Magnet
  • Onsite in 30 Minutes Guaranteed
  • Boots Off at the Door. Every Single Time.
  • 2,800+ Google Reviews and Counting
  • In the community For the community

THE SHORT ANSWER

In short

A dripping shower head usually means a worn washer or cartridge in the taps or mixer; a weak shower can be the supply, a valve or a failing part; and water showing up next to or below a bathroom can be a leaking shower. We have completed 453 shower repairs since 2019. You approve a fixed price before we start, and the work carries a lifetime labour warranty.

Licensed & Insured (NSW 285594C)

24/7 Emergency

$0 Call-Out in Business Hours

Upfront Fixed Pricing

Lifetime Labour Warranty

Family Owned

What is shower repair?

A shower repair fixes the plumbing that feeds your shower: the taps or mixer, the shower head and arm, the pipes behind the wall and the valves that control them. A shower that drains slowly is a drain job: see blocked showers. A shower that runs too hot or too cold can be the hot water system or its tempering valve: see below.

IS THIS THE RIGHT FIX?

When a repair is the right call

Most dripping showers need a new washer or cartridge, not a new mixer. If the mixer body is sound and parts are available, a repair is the quickest and lowest cost fix.

A new mixer makes more sense when the body is worn or corroded, the parts are no longer made, or you are renovating. If water is getting out of the shower recess itself, we find the leak first, and only open a wall or floor where the readings agree. How leak detection works.

A Proximity plumber at work

HOW IT WORKS

How shower repair works with us

1

Call a licensed plumber

Tell us what the shower is doing: dripping, weak, too hot, too cold or leaking. A real person answers, 24/7.

2

We’re there fast

Same-day service is available. If water is running and won’t stop, a licensed plumber is on site within 30 minutes, guaranteed, any hour.

3

Find the cause

We check the whole fixture, not just the drip you can see, and show you what has failed.

4

Fixed price first

A written scope and a fixed price you approve before any work starts.

5

Fix and test

The worn washer, cartridge or seal replaced with WaterMark certified parts, then tested at full flow, hot and cold.

6

Warranty

A lifetime labour warranty, plus the manufacturer warranty on any parts we fit.

FAULT BY FAULT

Common shower faults and the fix

FaultUsual causeThe fix
Shower head drips after it is offA worn washer in two-handle taps, or a worn cartridge in a mixerA new washer or cartridge
Leaks around the handle or mixerWorn seals inside the taps or mixerNew seals or a new cartridge
Weak showerA partly closed valve, a failing part, low supply pressure or a leak taking water firstThe cause found and fixed. Check the supply with the test below
Too hot, too cold or changing temperatureOften the hot water system or its tempering valveChecked on site. Hot water repairs
Damp next to or below the bathroomFailed waterproofing, grout, or the pipes behind the wallLeak found first, then repaired. Leak detection
Water slow to drainHair, soap and build-up in the wasteA drain job. Blocked shower

Repair or replace?

Evidence first. We show you the worn part or the leak readings before we recommend anything, and only suggest a new mixer when a repair won’t last. If the cause is failed waterproofing rather than the plumbing, we repair that too: we show you what we found and give you a fixed price for the repair before any work starts.

SHOWER TEMPERATURE

Too hot or too cold?

In NSW, water at the shower, bath, basin and bidet in a home must be no hotter than 50°C. A tempering valve or another approved device is required on every new heated water installation and every hot water heater replacement, including a like-for-like swap (Building Commission NSW).

The tempering valve mixes hot and cold water for the bathrooms, and it is the most common hot water repair in our job records. If your shower has turned too hot, too cold or keeps changing, that is one of the first things we check, along with the hot water system itself. See hot water repairs and hot water.

FROM OUR RECORDS

What we find on shower repair jobs

Where our plumbers recorded the cause on a shower repair job, these came up most often.

Cause our plumbers recordedJobs
Water leak123
Worn tap washer or cartridge25
Burst water pipe14
Silt and debris build-up12

From our job records (ServiceM8 and ServiceTitan), July 2019 to October 2026. Completed jobs only.

CHECK IT YOURSELF

Weak shower: check the supply first

Sydney Water aims to supply at least 15 metres head of pressure where your property connects, which equals about 18 litres a minute at the garden tap (Sydney Water: testing your water pressure).

  1. Make sure the tap on your water meter is fully on, and any taps that control the hot water system (Sydney Water).
  2. Turn everything off, read the meter, run the front garden tap fully for one minute, and read it again.
  3. If you got 18 litres or more, the supply is fine and the problem is in the shower or its pipes. If you got less, call Sydney Water on 13 20 90.

If only the hot side is weak, the problem is more likely the hot water system, a valve or the pipes feeding it. Tell us when you call.

KNOW YOUR SHOWER

Shower mixers, taps and diverters

What sits behind the handle decides what can wear out. Most of the valve is hidden in the wall, but nearly every repair is done from the front, through the handle and cover plate.

TypeHow it worksWhat wearsTypical sign
Two or three-handle tapsSeparate hot and cold taps, each with a washer or a ceramic disc valveThe washer and seat, or the ceramic cartridge, one side at a timeA drip from the rose, or one handle much stiffer than the other
Single lever mixerOne cartridge sets both the flow and the temperatureThe cartridge and its sealsA drip after use, a stiff lever, or a temperature that drifts
Thermostatic mixerA temperature-sensing cartridge holds the water at the setting you chooseScale and grit can stop the cartridge reactingTemperature swings when another tap or the toilet is used
DiverterSends water from the bath spout to the shower, or from a hand shower to an overhead roseThe diverter seals or cartridgeWater from both outlets at once, or a weak shower while the spout still dribbles

A diverter that no longer seals fully is an easy one to miss: the shower feels weak because part of the flow is escaping through the other outlet. We check it whenever a bath and shower share a mixer.

WEAK SHOWER?

Weak shower: what the pattern tells you

Once you have checked the supply with the meter test above, the way the shower is weak points to the cause.

What you noticeMost likely cause
Every tap in the house is weakThe supply: a meter tap not fully open, an old pressure reducing valve, corroded galvanised pipe or a leak taking water first
Only this shower, hot and coldA rose blocked with scale, a partly closed stop or isolation valve, a failing mixer cartridge or a leaking diverter
Only the hot sideThe hot water system, its valves or tempering valve, or the hot pipe feeding the bathroom
It drops when someone else uses waterThe pipework is struggling to feed two outlets at once, often in older homes
It changed when the shower head was replacedOften the new head is a water efficient one, by design

That last one is not a fault. Sydney Water says older showerheads use 15 to 25 litres a minute, while an efficient showerhead uses 6 to 7, and it recommends a WELS 4-star rated showerhead (Sydney Water: water saving tips). A good efficient head should still feel strong. If yours feels weak, we check the supply and valves before blaming the head.

THE SHOWER HEAD

Leaking shower roses and arms

  • The rose drips after the shower is off: the head is fine. The water is getting past a worn washer, cartridge or diverter in the valve behind the wall.
  • Water runs down the arm or sprays from the joint behind the head: the seal on the thread between the arm and the head has failed. A new seal fixes it.
  • Water leaks where the arm meets the wall: worth acting on quickly. The fitting the arm screws into sits inside the wall, so a leak there can soak the wall cavity.
  • Jets spray sideways or some nozzles are blocked: scale. If the head unscrews by hand, soaking it in white vinegar often clears it. Otherwise a new WELS rated head is a quick swap.

Damp, peeling paint or mould on the other side of the shower wall, or in the room below, usually means the leak is inside the wall or under the tiles, not at the rose.

FAILED WATERPROOFING

Failed shower waterproofing: the signs, the rules and the repair

Under the tiles, every shower needs a waterproof membrane. Grout and tiles are not waterproof on their own, so once the membrane fails, water travels into the walls, the floor and the rooms around the shower. The signs to look for:

  • Grout that is cracked, crumbling or missing, or silicone that has pulled away at the corners and the floor.
  • Tiles that sound hollow when tapped, or that have lifted or cracked.
  • Paint bubbling, swollen skirting boards or door frames, or mould on the far side of the shower wall.
  • A stain on the ceiling below, or water at the edge of the carpet in the next room.
  • A musty smell that comes back after cleaning.

The rules. The National Construction Code sets what must be waterproofed in a home’s wet areas. The Australian Building Codes Board explains that under NCC 2022 the floor of the shower area must be waterproofed and the walls of the shower area must be waterproofed to a height of 1800mm (ABCB: waterproofing in houses). In NSW, waterproofing is licensed trade work: a contractor licence is needed for residential waterproofing work valued at more than $5,000 in labour and materials, including GST (NSW Government: waterproofing work).

How we tell a plumbing leak from failed waterproofing. We pressure test the pipes and mixer behind the wall, then take moisture readings with the shower dry and again after it has run. If the pipes hold pressure but the readings rise only when water is on the shower floor or walls, the membrane or grout is the path. We repair failed shower waterproofing, and you get a fixed price for the repair before any work starts. In an apartment, see who pays for strata plumbing; renting, see plumbing help for tenants; and for cover, plumbing emergencies and insurance.

NEW MIXERS AND SHOWER HEADS

WaterMark certified parts, every time

Plumbing products of a type on the WaterMark Schedule of Products must be WaterMark certified, and a licensed plumber is not permitted to install one that isn’t (WaterMark: buying plumbing products). Products bought online can still be uncertified, and using one where certification is required can mean replacing it, a product failure that damages the building, or possibly a voided insurance claim. Look for the WaterMark and its licence number on the product or box, or search the WaterMark product database before you buy.

FAST PLUMBING HELP

Need this sorted today?

Same-day help from a licensed 24/7 plumber, on site within 30 minutes, guaranteed, when water won’t stop, and a fixed price before we start.

$0 Call-Out in business hours

30-Min Response

24/7 Plumber

Lifetime Labour Warranty

WHAT IT COSTS

What shower repair costs

Since 2019 our licensed plumbers have completed 453 shower repair jobs across Sydney. Half of our 437 priced shower repair jobs since 2019 cost between $308 and $1,319, including GST, with a median of $462.

You approve a fixed price before any work starts, never an hourly meter. $0 call-out Monday to Friday, 7:00am to 3:00pm, and Saturday, 7:00am to 12:00pm. Outside those times, and all day on NSW public holidays, the call-out fee is $385 ($350 plus GST), paid before we send a plumber.

If we find something the quote didn’t cover, we stop and give you a revised fixed price before continuing.

See how our pricing works.

WHERE WE’VE DONE THIS

Where we’ve done the most shower repair work

The suburbs where we’ve done the most shower repair work since 2019.

From our job records (ServiceM8 and ServiceTitan), July 2019 to October 2026. Completed jobs only.

Reviews

The proof we’re proudest of

4.9 / 5.0

from 2,800+ Google reviews

More than two thousand Sydney households have shared their experience.

Based on 2,800+ Google reviews


Reviewed by William Demirdonder, Director and licensed plumber (NSW licence 275278C, supervisor for Proximity Plumbing’s contractor licence 285594C). Last reviewed 9 November 2026.

AT A GLANCE

Key facts

Service

Shower Repairs

Available

24/7, 365 days a year

Call-out fee

$0 Monday to Friday, 7:00am to 3:00pm, and Saturday, 7:00am to 12:00pm. $385 outside those times and on NSW public holidays

Pricing

Fixed price you approve before any work

Licence

NSW Contractor Licence 285594C

Warranty

Lifetime labour warranty

Jobs since 2019

453

QUESTIONS

Shower Repairs questions

RELATED SERVICES

Related help

SYDNEY’S 24/7 PLUMBER

Ready when you are

Book online in seconds or call now: a fixed price before we start, $0 call-out in business hours and a lifetime labour warranty on every job.

Licensed NSW 285594C

$0 call-out in business hours

Lifetime labour warranty

4.9★ (2,800+ reviews)