
What’s in Sydney Tap Water?
Chlorine, fluoride, hardness, PFAS and lead: what is in the water at your tap, and what it means for your family.
$0 CALLOUT FEE IN BUSINESS HOURS | FREE QUOTES | SAME DAY SERVICE

NOW SERVICING NORTH SYDNEY
WE ARE AVAILABLE
- 35+ Years of Combined Experience
- Yes, a Real Plumber Reads These Messages Too
- The Kettle Is Always On at Head Office
- $0 Call Out Fees
- Every Job Photographed, Every Price Upfront
- We Answer the Phone. Revolutionary, We Know.
- Trusted by 15,000+ Sydney Families
- No Call Centres. You Get a Human in Sydney
- Your Neighbours Probably Have Our Fridge Magnet
- Onsite in 30 Minutes Guaranteed
- Boots Off at the Door. Every Single Time.
- 2,800+ Google Reviews and Counting
- In the community For the community
THE SHORT ANSWER
In short
Sydney’s tap water is treated, tested and safe to drink: Sydney Water says it meets the Australian Drinking Water Guidelines. It contains small amounts of chlorine (with ammonia, which makes chloramine) to keep it safe to your tap, fluoride at a target of 1 mg/L, and natural minerals: at about 57 mg/L of hardness, Sydney water is soft. PFAS is tested weekly and Sydney Water says it is below the guideline values. What can change at your tap is your own pipes: old solder and brass fittings can add lead, and old pipes can add rust.
WHERE IT COMES FROM
From the dam to your tap
Most of Sydney’s water comes from Warragamba and the other dams run by WaterNSW. Sydney Water treats it at 9 filtration plants. The largest, Prospect, supplies drinking water to over 4.2 million customers and 85% of Greater Sydney (Sydney Water). From the plants it is piped through reservoirs to your street.
Sydney Water publishes the results. Enter your address on its water analysis page to see the figures for your area, or call 13 20 92 (8am to 5:30pm, Monday to Friday) for help. The daily drinking water quality report confirms the plants are meeting the guidelines.
WHAT IS ADDED
What Sydney Water adds, and why
| What | Why | How much |
|---|---|---|
| Chlorine | Kills germs and keeps the water safe all the way to your tap | Typically about 0.2 to 0.5 mg/L in Australian pipe networks; the health guideline value is 5 mg/L |
| Chloramine | Chlorine plus a little ammonia: lasts longer in long pipelines | Sydney Water says chlorine and ammonia are present at low and safe concentrations |
| Fluoride | Added on NSW Health’s advice for teeth, under the Fluoridation of Public Water Supplies Act 1957 | Target 1.0 mg/L; NSW Health requires results between 0.9 and 1.5 mg/L |
Chlorine figures are from the Australian Drinking Water Guidelines; the fluoride range is from NSW Health’s fluoridation requirements. The guidelines’ health limit for fluoride is 1.5 mg/L (NHMRC).
Facts checked 9 November 2026. Sources: Sydney Water, NSW Health, Standards Australia and Puretec.
TASTE AND SMELL
Why your water can smell of chlorine
The guidelines put chlorine’s odour threshold at about 0.6 mg/L, and some people notice it from about 0.2 mg/L. Water suppliers sometimes need to go above 0.6 mg/L to keep enough disinfectant in the water at the far ends of the network, so homes nearer a dosing point can notice it more.
Chlorine slowly leaves water that stands in an open container: Sydney Water suggests 48 hours for aquarium water, though chloramine needs a water conditioner. For drinking, a carbon filter is the reliable way to take the taste and smell out.
WHAT IS NATURALLY IN IT
Minerals and hardness
Hardness is the calcium and magnesium in water, measured as mg/L of calcium carbonate. Sydney Water says Greater Sydney’s water is about 57 mg/L, and anything under 60 mg/L counts as soft.
That is why most Sydney homes on mains water do not need a water softener. Some European dishwashers ask for hardness in mmol/L: Sydney Water says 57 mg/L is 0.57 mmol/L, so set yours to suit soft water. Scale on taps and shower heads is usually small; a whole house filter with scale control helps if you see build-up.
PFAS
PFAS in Sydney water
PFAS are long-lasting man-made chemicals. Sydney Water says all 9 of its filtration plants supply water below the guideline values, that it tests treated water and publishes the results weekly, and that your drinking water does not require additional treatment. The guidelines were tightened in June 2025: PFOS 8 ng/L, PFHxS 30 ng/L, PFOA 200 ng/L and PFBS 1,000 ng/L (Sydney Water’s PFAS page).
FROM YOUR OWN PIPES
What your home’s pipes can add
The water leaving Sydney Water’s system does not carry lead, but old solder and brass fittings inside some older homes can, and copper and lead build up most in water that has been standing. Old galvanised pipes can add rust.
NSW Health’s advice: run the cold taps you use for drinking and cooking for about 10 seconds first thing each morning, and for at least 2 minutes after the water has been standing for a long time, such as after a holiday. Use the flushed water on the garden or for washing up (NSW Health).
The rules for new fittings are tightening. From 1 May 2026, makers can only produce Lead Free WaterMark certified products for drinking water, meaning a weighted average lead content of no more than 0.25%, and from 1 May 2028 plumbers will need to look for the Lead Free WaterMark on what they install (WaterMark). We can replace old fittings now, or fit an under-sink filter certified to NSF/ANSI 53 for lead.
WHAT YOU SEE AT THE TAP
What it means when your water looks or smells different
| What you notice | Usually | What to do |
|---|---|---|
| A chlorine smell | Disinfectant in the water, strongest near a dosing point | Nothing unsafe; a carbon filter removes it |
| Milky water that clears from the bottom up | Tiny air bubbles | Let the glass stand; it clears on its own |
| Brown or rusty water | Sediment stirred up by mains work, or rust from old galvanised pipes | Run the cold tap until it clears; if it keeps happening, have your pipes checked |
| Water that tastes metallic first thing | Water that has stood overnight in older pipes and fittings | Flush the cold tap as NSW Health advises |
| White scale on taps and shower heads | Calcium deposits, usually light on Sydney’s soft water | Clean with vinegar; consider scale control if it is heavy |
For old pipework, see how old are your building’s pipes? and our general plumbing services.
DO YOU NEED A FILTER?
So, do you need a filter?
Not for safety on mains water: NSW Health says there is generally no need to filter tap water that has already been treated. Families choose a filter for taste and smell, for older pipes, for rainwater, or for the peace of mind of an extra barrier.
If you do buy one, NSW Health says it should be certified to an appropriate standard such as NSF/ANSI 42 and 53, and maintained and replaced regularly. See every type of water filter, explained, or whole house or under sink?
QUESTIONS
Questions
WATER FILTER GUIDES
Read next

CLEAN WATER FOR YOUR FAMILY
Talk to us about your water
A licensed plumber will tell you honestly what your home needs, if anything, and give you a fixed price before any work starts. $0 call-out Monday to Friday, 7:00am to 3:00pm, and Saturday, 7:00am to 12:00pm. Outside those times, and all day on NSW public holidays, the call-out fee is $385 ($350 plus GST), paid before we send a plumber.
Every enquiry answered in 15 minutes
Lifetime labour warranty
4.9 from 3,000+ reviews

