Pipe Patching (Patch Relining)

One damaged spot repaired from the inside, with no digging.

$0 CALLOUT FEE IN BUSINESS HOURS | FREE QUOTES | SAME DAY SERVICE

Google

Overall Rating

4.9

Five stars

(3,000+)

Brightest & Best Business Awards: Winner 2019, Winner 2024, Winner 2025, People's Choice 2025, Finalist 2023

NOW SERVICING NORTH SYDNEY

  • 35+ Years of Combined Experience
  • Yes, a Real Plumber Reads These Messages Too
  • The Kettle Is Always On at Head Office
  • $0 Call Out Fees
  • Every Job Photographed, Every Price Upfront
  • We Answer the Phone. Revolutionary, We Know.
  • Trusted by 15,000+ Sydney Families
  • No Call Centres. You Get a Human in Sydney
  • Your Neighbours Probably Have Our Fridge Magnet
  • Onsite in 30 Minutes Guaranteed
  • Boots Off at the Door. Every Single Time.
  • 3,000+ Google Reviews and Counting
  • In the community For the community

THE SHORT ANSWER

In short

A patch liner repairs one damaged spot, such as a crack, a root entry point or a leaking joint, without lining the whole pipe. It spans the defect and runs a short way past it on each side. It is the right fix when the rest of the pipe is sound, which a CCTV inspection shows. Our patch repairs carry the same 35-year installation guarantee as a full liner.

Licensed & Insured (NSW 285594C)

24/7 Emergency

$0 Call-Out in Business Hours

Upfront Fixed Pricing

Lifetime Labour Warranty

Family Owned

HOW A PATCH WORKS

What a patch liner is, and how it goes in

A patch liner is a short sleeve of fabric, called the carrier, soaked in resin and wrapped around a packer: a rubber bladder on the end of a push rod or cable. Watching on a camera, the installer moves the packer along the pipe to the defect, then inflates it. The bladder presses the resin-soaked sleeve against the old pipe wall, and holds it there while the resin cures. Then the packer is deflated and pulled out, leaving a full circle of new pipe wall over the crack, hole or joint, bonded to the old pipe on each side.

BRAWO SYSTEMS, the maker of Brawoliner, sells its own short repair kit on this principle: a seamless carrier that copes with changes in pipe size, a two-part epoxy resin that cures at normal temperature, and a packer whose bladder expands from the centre outwards so the sleeve goes on without creases (BRAWO SYSTEMS).

Sydney Water’s own specifications treat a patch liner, a full circle of liner over a short length of pipe, as lining under its lining specification (SS 201), and keep it separate from robotic repairs that fill cracks with mortar (SS 202). The difference matters: a patch is a new pipe wall in its own right, not a filler that relies on the old pipe around it.

Words you will hear

  • Host pipe: the old pipe being repaired.
  • Defect: the crack, hole, root entry point or leaking joint the patch covers.
  • Packer: the inflatable bladder that carries the patch and presses it in place.
  • Junction: where a branch pipe joins. A patch over a junction is cut open again afterwards.

PATCH OR FULL LINER?

When a patch is the right repair

SituationBest repair
One crack, hole or root entry point, rest of the pipe soundA patch liner
Two or three defects close togetherA patch over them, or a short liner, depending on spacing
Defects along the pipe, or old earthenware with many jointsA full-length liner: patching each one costs more and leaves the joints between
A sag or collapsed sectionDig up and replace that section

Sydney Water’s rule for localised repairs inside its own sewers is that a repair covers the full length of the damage, plus extra length to blend into sound pipe on each side, and it treats any repairs within 1,200 mm of each other along the pipe as one repair (SS 202). Both are sound rules for a patch on a private drain too. We measure every defect on camera before we choose the patch length.

WILL A PATCH WORK?

Defects a patch can and can’t fix

What the camera showsCan a patch fix it?Why
A single crack around the pipeYesThe classic patch repair: one short sleeve seals it.
Roots growing in at one jointYes, once the roots are cut outThe patch covers the joint the roots used, so there is no gap left for them.
A small hole or broken pieceUsuallyIf the pipe around it is sound, the patch bridges the hole. If pieces are missing over a long length, it needs a liner or a dig.
A joint that has moved slightly out of lineUsuallyA small step can be patched over. A badly offset joint leaves a lip the patch can’t sit flat against.
A crack running along the pipeSometimesA long split often means the pipe is under load along its length, which suits a longer liner better.
Defects every metre or twoNo, line itSeparate patches cost more than one liner and leave the joints between them open to roots.
A sag or a collapsed sectionNoA patch follows the pipe’s shape, so water still sits in a sag. A collapse is dug up and replaced.

The camera decides it. If a patch is not the right repair for your pipe, we tell you and quote the repair that is.

STEP BY STEP

How a patch repair is done

Every patch repair follows these six steps, through an existing access point such as an inspection opening, with no digging.

1

Camera and measure

A CCTV camera finds the defect and measures how far it is from the access point, how long it is, and what the pipe looks like on either side.

2

Clean and cut roots

Roots and build-up are cleared with a high-pressure water jetter and, where needed, a robotic cutter, so the patch bonds to clean pipe.

3

Stop the water

Nobody in the house uses the toilets, showers or sinks on that drain while the patch goes in and cures. We tell you when to stop and when it is safe again.

4

Prepare the patch

The carrier is cut to length so it spans the defect and runs into sound pipe each side, then soaked in resin and wrapped on the packer.

5

Place, inflate and cure

The packer is positioned on camera, inflated against the pipe wall and held there until the resin has cured, then deflated and removed.

6

Check and report

A second camera run shows the finished patch. You get the footage before and after, and a written report.

YOUR OPTIONS

Patch, full liner or dig: how they compare

Patch linerFull-length linerDig and replace
Best forOne defect, or two or three close together, in an otherwise sound pipeSeveral defects, old clay pipe with many joints, roots along the lineSags, wrong grade, collapsed pipe
DiggingNoneNoneA trench over the damaged length
Protects the rest of the pipeNo, only the spot it coversYes, the whole lined lengthOnly the new section
DisruptionUsually a few hoursMost homes are done in a dayDays, plus rebuilding paths, gardens or driveways
Guarantee35-year installation guarantee35-year installation guaranteeOur lifetime labour warranty

A patch is not always much cheaper than a liner. On our records, the median patch job cost $5,738 and the median relining job $6,530, including GST, because the camera work, cleaning, root cutting and set-up are much the same whatever the length. That is why, once there are several defects, one liner is often better value than several patches.

WHAT IT COSTS

What a patch repair costs

Our records show 28 priced patch repairs since 2019, with half costing between $3,983 and $8,122 and a median of $5,738, including GST. That includes the CCTV inspections, cleaning and root cutting the repair needs. You get a fixed price before work starts. If we find something the quote didn’t cover, we stop and give you a revised fixed price before continuing.

The price moves with how far the defect is from an access point, how heavy the roots are, the pipe size, and whether a junction has to be reopened. See pipe relining cost in Sydney for how relining and patching are priced.

BEFORE YOU SAY YES

Questions to ask about a patch repair

  • How long is the patch, and how far past the defect does it run on each side?
  • What does the rest of the pipe look like on the footage? Will I need more repairs soon?
  • Is there a junction near the defect, and how will it be reopened?
  • Will I get the CCTV footage from before and after, and a written report?
  • What does the guarantee cover, and for how long?
  • If roots come back somewhere else on the line, what are my options then?

You should get a straight answer to every one of these from us. See how to read a CCTV drain report to make sense of the footage.

FROM OUR JOB RECORDS

Patch repairs in our records

Since 2019 we have completed 30 pipe patching jobs. Where a cause was recorded, tree roots in the drain line came first (3 jobs), then a broken or displaced pipe section. Most were in Randwick, Rose Bay and Paddington.

Most patch repairs start the same way: a drain blocks, it is cleared, and the camera shows one root entry point or crack in an otherwise sound pipe. Clearing the roots again and again treats the symptom; the patch removes the gap they come back through. If the camera shows more than one or two defects, we will suggest a full liner instead.

OUR GUARANTEE

A 35-year guarantee and a 50-year life expectancy

Every Brawoliner we install carries our 35-year installation guarantee, and the liner has a 50-year life expectancy.

Our labour also carries a lifetime labour warranty, for as long as you own or occupy the property. Your written report and the CCTV footage before and after are your record of the work.

CASE STUDIES

Relining jobs we have done

AT A GLANCE

Key facts

Service

Pipe patching (patch relining)

System

Brawoliner

Guarantee

35 years on the installation

Liner life

50 years expected

Labour

Lifetime labour warranty

Call-out

$0 call-out Monday to Friday, 7:00am to 3:00pm, and Saturday, 7:00am to 12:00pm. Outside those times, and all day on NSW public holidays, the call-out fee is $385 ($350 plus GST), paid before we send a plumber.

Licence

NSW 285594C

Since

2015

QUESTIONS

Pipe patching questions

EXPLORE

Pipe relining

PIPE RELINING SPECIALISTS

Talk to a relining specialist

A licensed plumber inspects the pipe with a CCTV camera and gives you a written report and a fixed price before any work starts.

Licensed NSW 285594C

$0 call-out in business hours

35-year relining guarantee

4.9 from 3,000+ reviews