Robotic Cutting and Junction Reinstatement

Every branch reopened, flush and sealed, and shown on camera.

$0 CALLOUT FEE IN BUSINESS HOURS | FREE QUOTES | SAME DAY SERVICE

Google

Overall Rating

4.9

Five stars

(3,000+)

Brightest & Best Business Awards: Winner 2019, Winner 2024, Winner 2025, People's Choice 2025, Finalist 2023

NOW SERVICING NORTH SYDNEY

  • 35+ Years of Combined Experience
  • Yes, a Real Plumber Reads These Messages Too
  • The Kettle Is Always On at Head Office
  • $0 Call Out Fees
  • Every Job Photographed, Every Price Upfront
  • We Answer the Phone. Revolutionary, We Know.
  • Trusted by 15,000+ Sydney Families
  • No Call Centres. You Get a Human in Sydney
  • Your Neighbours Probably Have Our Fridge Magnet
  • Onsite in 30 Minutes Guaranteed
  • Boots Off at the Door. Every Single Time.
  • 3,000+ Google Reviews and Counting
  • In the community For the community

THE SHORT ANSWER

In short

A relined pipe is only finished when every branch that feeds it is open again. A robotic cutter, guided by camera from inside the pipe, cuts the liner away from each live junction, leaving a smooth edge flush with the branch. The same cutter removes roots and hard build-up before lining. Junctions can then be sealed so roots cannot get in where the branch meets the main.

Licensed & Insured (NSW 285594C)

24/7 Emergency

$0 Call-Out in Business Hours

Upfront Fixed Pricing

Lifetime Labour Warranty

Family Owned

THE TOOL

What a robotic cutter is

A robotic cutter is a small motorised unit that travels inside the pipe on a cable or push rod, carrying a camera and a cutting head, usually a spinning burr or grinding bit. The operator stays above ground, watching the camera and steering the head: turning it, raising it and pushing it into the pipe wall or a junction, a few millimetres at a time.

Sydney Water calls these remote controlled devices. Its specification for repairs from inside the pipe expects them to be run by trained, experienced operators who can see the work area on camera the whole time, and lists the jobs they do: removing obstructions such as tree roots, restoring junctions and preparing cracks and joints for repair (SS 202).

What it is used for

  • Before lining: cutting out roots, hard scale and concrete, and trimming a branch pipe that sticks into the main line, so the liner sits against clean, smooth pipe.
  • After lining: cutting the liner open at each live junction so the branch drains again.
  • Fixing earlier work: reopening a junction another installer left closed or cut roughly, and trimming a liner’s lifted end. See failed relining repair.

JUNCTIONS

Why reopening junctions properly matters

  • Before lining, we confirm which junctions are live, using a dye test where needed, so none is missed
  • Each opening is cut back with a smooth, bevelled edge, flush with the branch, so it does not restrict flow or catch waste (Sydney Water SS 201)
  • If a relining job leaves a live junction closed, the branch it serves blocks and has to be reopened
  • Every reopened junction is shown on the final CCTV run and listed in your report

STEP BY STEP

How a junction is reopened after lining

On Sydney Water’s own sewers, its lining specification sets this order, and asks for a rough cut on the day of lining and the final cut only once the liner has settled to its final size (SS 201).

1

Map every junction

Before lining, the camera records each branch: its distance from the access point and where it sits around the pipe, such as the 2 o’clock position.

2

Prove which are live

Where the camera cannot tell, coloured water is run down the fixture upstream. If it shows at the junction on camera, the branch is live.

3

Clean the junction

Roots and debris are cleared from the junction into the branch, so the liner and any seal bond to clean pipe.

4

Line the pipe

The liner goes in and cures, covering every junction. A slight dimple in the liner usually shows where each branch is.

5

Cut and finish

The cutter opens each live junction, then finishes the edge smooth, bevelled and flush with the branch, with nothing left to catch waste.

6

Seal and check

Where roots or leaks are a risk, a junction seal goes in last. The final camera run shows every opening, and each one is listed in your report.

LIVE OR DEAD?

Live and dead junctions

A live junction still carries water from a toilet, shower, sink, downpipe or another property. A dead junction no longer does: the fixture was removed, the bathroom was moved, or an old connection was abandoned during a renovation.

On its sewers Sydney Water asks for the location of every live and dead junction to be recorded before lining, and for only live junctions to be reopened (SS 201). A dead junction left sealed behind the liner is a good outcome: it is one less opening for roots to find. A live junction left sealed is the opposite, and it is a common reason a drain blocks soon after relining.

If you have changed bathrooms, laundries or downpipes over the years, tell us before the job. It helps us know which branches should be running.

JUNCTION SEALS

Sealing junctions against roots

Where a branch meets the relined pipe, a junction seal finishes the job. A top hat seal sits in the junction like the brim of a hat; a T-seal also wraps the main pipe. Sydney Water’s specification requires junction seals on its sewers to reach at least 400 mm into the branch and 150 mm past its first joint, to stop leaks and roots, with a 50-year service life (SS 207). Brawoliner’s system includes a connection collar for reinstating side inlets.

HOW SEALS ARE SPECIFIED

What a good junction seal looks like

  • A T-seal’s arm in the main pipe is at least four times the branch’s diameter long, and runs at least one and a half times that diameter past the junction on each side (Sydney Water SS 207).
  • Where both the main pipe and the branch are lined, the junction seal goes in last.
  • Seals must be strong enough not to be damaged by jetting at 14 MPa (about 2,000 PSI) at 5 litres a second, so a sealed junction can still be cleared if something blocks it later.
  • Unacceptable on Sydney Water work: bubbles, voids or blisters, gaps between the seal and the pipe, leaks, poor finishing at the ends, and seals that have not cured.
  • Sydney Water notes extra risks in sealing a junction on a pipe that has not been lined, so a seal on an unlined pipe is a considered choice, not a default.

These are Sydney Water’s rules for its own sewers (SS 207); on a private drain they are a useful benchmark for what to expect.

ROOT CUTTING

Cutting roots before lining

A liner has to sit against clean pipe. The Brawoliner approval requires roots, protruding inlets and hard build-up to be removed first, with tools that do not damage the pipe further (DIBt). We cut roots out with the robotic cutter and a high-pressure water jetter, then check the pipe on camera before lining.

WHAT GOES WRONG

Junction problems: sign, cause and fix

What you noticeUsual causeThe fix
A shower, basin or toilet drains slowly after reliningA junction not reopened, or only partly openedRecut the opening to the full size of the branch
Paper or waste keeps catching at one spotA rough or ragged edge where the liner was cutGrind the edge smooth and flush with the branch
Roots return at a branch after reliningNo seal where the branch meets the lined pipeClear the roots and fit a junction seal
A branch pipe pokes into the main lineA poor connection when the pipe was first laidCut it back flush before lining
Hard lumps or concrete in the pipeOld repairs, mortar or scale build-upGrind them out so the liner sits flat

Finish standard from Sydney Water: openings must not restrict flow or catch solids (SS 201).

MYTH OR FACT

Robotic cutting: myths and facts

MythFact
Cutting the roots out fixes the drain.It clears it. The crack or joint the roots came through is still there, so they grow back. Relining or a patch closes the gap.
Relining blocks off your other drains.Only if a junction is missed. Every live junction is found before lining and reopened after, and you see each one on the final footage.
A robotic cutter damages the pipe.Used properly it doesn’t: the operator works on camera, a few millimetres at a time, and stops at the pipe wall.
You have to dig to reach a junction.No. The cutter goes in through the same access point as the camera and the liner.

BEFORE YOU SAY YES

Questions to ask your relining plumber

  • How many junctions are on my line, and which of them are live?
  • How will you prove a junction is live if the camera can’t tell?
  • Will every reopened junction be shown on the final footage and listed in the report?
  • Will any junctions be sealed, and with what?
  • If a branch drains slowly after the job, what happens?

Our answers: we map every junction, dye test where needed, and reopen and show each live one on the final footage. Read more about the full job on pipe relining, or see what it costs on pipe relining cost in Sydney.

CASE STUDIES

Relining jobs we have done

AT A GLANCE

Key facts

Service

Robotic cutting and junction reinstatement

System

Brawoliner

Guarantee

35 years on the installation

Liner life

50 years expected

Labour

Lifetime labour warranty

Call-out

$0 call-out Monday to Friday, 7:00am to 3:00pm, and Saturday, 7:00am to 12:00pm. Outside those times, and all day on NSW public holidays, the call-out fee is $385 ($350 plus GST), paid before we send a plumber.

Licence

NSW 285594C

Since

2015

QUESTIONS

Robotic cutting questions

EXPLORE

Pipe relining

PIPE RELINING SPECIALISTS

Talk to a relining specialist

A licensed plumber inspects the pipe with a CCTV camera and gives you a written report and a fixed price before any work starts.

Licensed NSW 285594C

$0 call-out in business hours

35-year relining guarantee

4.9 from 3,000+ reviews