We Are The Most Highly Rated North Wahroonga Plumber
Familiar Faces
How Much Should It Cost To Have A Hot Water Heater Installed?
The average cost of installing a new hot water system in Australia is between $200 and $600. However, this is only the case if you’re replacing an existing hot water system with one of the exact same type, and this does not factor the cost of the water heater unit itself into account.
First, you will need to consider the size of the water heater you need in your home. Water heaters with a higher tank capacity or heating capacity will always be more expensive than smaller units. This is true whether you choose an electric system like a heat pump water heater, a solar water heater, or a water heater powered by natural gas.
So we highly recommend consulting with an experienced plumber and discussing how much hot water your home needs. Tanks can vary in size from 25L all the way up to 400L, and tankless, on-demand heaters vary greatly in capacity, too. Choosing the right size will help you save money when installing and operating your water heater.
New Hot Water Heater Installation Prices
Hot Water Repairs for North Wahroonga Residents
Every household should have a hot water system that is running efficiently and effectively. If you notice any of the below signs, you know you have a bigger problems
• Leaks in the tank - If from the bottom, this can happen from years of sediment build-up and rust Another cause could be from incorrect initial installation or old age. If the problem is located at the top, then it could be a loose valve or pipefitting.
• The temperature has changed to cold - The reason could be dependent on what energy source you are running off. If you have gas, there could be no gas supply, or your pilot light has turned off. For electrical tanks, the thermostat could be busted, or the heating element could be faulty.
• Hot water running out regularly - The size of your container may not be big enough to handle your usage. Your boiler could be struggling to provide sufficient heating, particularly if you have an instantaneous system and a large household.
• Large water bills - Your bill may be skyrocketing if a leak is located somewhere in the unit • Noisy Tank - A build-up of sediment is the most common cause of a noisy tank. Naturally, H20 has material deposits inside of it, and it will settle down the bottom. The sediment pieces end up swirling around the inside, hitting the cylinder,
If you are experiencing issues such as a leaking system, low pressure, or no warm water, it is safe to say you require a replacement unit or at the very least, the right repairs made.
What To Do In A Plumbing Emergency
1. Call
Call our Proximity Plumbing team immediately and we will dispatch the closest Hot Water in the Eastern Suburbs to your residence or office.
2. Isolate
2. Proximity Plumbing will advise how to isolate the Hot Water supply to your Hot Water meter and offer support over the phone in the interim of the plumber arriving.
3. Turn Off
3. You can turn off all your Hot Water appliances in your home including Hot Water cooking appliances, heaters, and Hot Water units (including the pilot).
4. We’re Here
By this time one of our expert team members will be onsite.
How Long Should A Hot Water Tank Last?
A properly installed and high-quality hot water tank will last between 8 to 12 years. Like everything else, time and consistent use will wear down the tank. If your hot water system has reached 15-20 years old and has started being noisy and failing to give you the hot water you need consistently, it’s probably at the end of its life.
If you’re in an older property without any information about when the hot water system was installed, it’s a good idea to get a professional plumber to come and take a look to determine whether it can be repaired.
Please note that getting these levels of life expectancy from the hot water systems is only feasible with attention to hot water system maintenance. For instance, you may need to replace parts like anodes every five years to keep the system in the best shape.
If you’re searching for North Wahroonga hot water service or installation, look no further. Your local North Wahroonga hot water plumber can handle this for you and we can provide the best hot water solution to suite your home and your requirements.
North Wahroonga Hot Water Repair Specialists Providing Complimentary Quotes. Call Us Now For Free Consultation:
0420 102 394 What is The Best Hot Water System In Australia?
The EVO270 has won the 2021, 2020 & 2019 hot water Product Review Award for 3 consecutive years, even after being recognised by Australian customers because of its innovative energy efficiencies and intelligent features.
It has been considered the next evolution in water heating, with advanced energy efficiency technologies and built-in smart features to ensure you’re provided with clean, safe, and economical hot water all year round.
The EVO 270 has innovative energy efficiency technology and constructed with smart features to guarantee you’re supplied with clean, secure, and affordable warm water throughout the year.
Unlike conventional hot water systems which use 1kW of electricity to produce 1kW of warmth, the EVO 270 uses the same 1kW of power and heat pump technologies to create 4kW of warmth — saving you around 75 percent of your hot water prices!
Key Points:
1. Hot water up to 70°C
2. Storage Capacity: 270 litres
3. Locations: Outdoor or Indoor.
Brands we Supply, service & install
Average Hot Water System Running Costs
It’s up to 40% cheaper than electricity to use and up to 50% cheaper to maintain and service with fewer parts. Unlike electricity, where increased consumption drives your tariffs higher, generally the more gas appliances you install the more you can save. This is because in most cases, the cost per unit of the gas decreases as consumption increases.
About North Wahroonga
North Wahroonga is a suburb on the Upper North Shore of Sydney, in the state of New South Wales, Australia. North Wahroonga is located 23 kilometres north-west of the Sydney central business district, in the local government area of Ku-ring-gai Council. Wahroonga is a separate suburb, to the south.
North Wahroonga is bounded by the F3 Sydney-Newcastle Freeway on the west and the Ku-ring-gai Chase National Park on the north.
Why Choose Us For Your Hot Water Service?
Proximity Plumbing prides itself at providing a minimum of three options to tackle a Hot Water system fault. Depending on the source of the Hot Water will determine the appropriate method whether it’s repairing the Hot Water leak, upgrading your hot water unit or just a general hot water service.
Using Hot Water detecting equipment is the first crucial step in making your property safe again, and in the long term, attending to Hot Water leaks swiftly means you save money by not paying inflated Hot Water bills due to leaking Hot Water. In some circumstances, we can provide an option that may be an energy-efficient hot water system that suits your budget and meets a high energy star rating.
We are licensed hot water specialists that are licensed to install & service all types of hot water systems, when dealing with us you will have a lifetime labour warranty & manufacturers warranty. Proximity Plumbing doesn’t take shortcuts when installing a hot water tank in your home, we ensure everything is to code including supplying a mandatory tempering valve to ensure no one gets burnt from scalding hot water.
No Obligation Free Quotes.
Over A Thousand + Successful Jobs For Clients Within The Eastern Suburbs.
One Of Few Plumbers Who Successful Carry Out Relining For Other Plumbers.
We provide you with the recommendations to remedy the problem.
We discuss their options for immediate works if required.
We provide annual inspections and ongoing maintenance on our completed works so they know that their investment is safe.
Repair Hot Water System Issues Asap
Don't Put Yours, Your Family Or Your Property At Risk
Which hot water brand is best suited for my home?
Did you know Proximity Plumbing have helped over 5400 + homes get their hot water up & running throughout the last 10 years, we know having hot water is crucial and thankfully we know what’s best to recommend thanks to being partners with Reece plumbing- when looking for what the best hot water system is for your home we always recommend determining the following points :
Tank Size- What size of hot water is best suited for my home? - this will depend if you live in an apartment or a house & how many people live within your home- rest assured our Local Eastern suburb plumbers will assist with making the most cost-effective/ suited size for your home.
Space- How big are hot water tanks? Hot water tanks vary in size if gas isn’t an option in your home our Eastern suburbs hot water expects can provide other solutions.
I have Gas: Gas vs electric hot water? if gas is available we always recommend installing a gas hot water system as they are cost-effective, easy to service & better for the environment.
Tempering Valves & How They Work
A tempering valve is one of the best ways to ensure people are not harmed or scalded by hot water when it comes out of a faucet. It works as a mixing tool, as it combines both cold and hot water to correctly produce the required water temperature to be released from a particular outlet.
Tempering valves work by allowing the 60 c water inside the unit to be mixed with cold water and then safely flow out of the faucet with a temperature of 45 c to 50 c. For some institutions such as young, aged, sick and disabled facilities eg, nursing homes, the maximum delivery temperature should not exceed 45 c.
According to Australian Standard AS3500.4.2 Clause 1.6 water temperature that comes out of the taps must not exceed 50 c but to prevent legionella bacteria from developing inside the tank the temperature must always be at 60 c.
Tempering valves work by allowing the 60 c water inside the unit to be mixed with cold water and then safely flow out of the faucet with a temperature of 45 c to 50 c. For some institutions such as young, aged, sick, and disabled facilities e.g., nursing homes, the maximum delivery temperature should not exceed 45 c.
How long it takes for hot water to burn
- 68°C1 Second
- 60°C 5 Seconds
- 52°C1 Minute
- 48°C5 Minutes
- 38°CSafe bathing temperature
Time to Produce Burn
Types Of Heating We've Worked On In The Eastern Suburbs
Storage Hot Water Heaters
These heaters can come in both electric and gas, with electric options you can also choose to go with off-peak power to save money on larger models.
Instantaneous Hot Water Heaters
Approximately 30 to 45 per cent lower running costs than their electric counterparts.
Solar Hot Water Heaters
A solar water heater works just like a battery, storing energy from the sun in the form of hot water, ready for use at a later time
Heat Pump Hot Water
A heat pump uses renewable energy to heat and absorb the heat from the surrounding air and use it to heat your water.
Electric Hot Water Heaters
Sizes ranging from 250-400 litres and come in all brands and models for any application.
Gas Hot Water Heaters
It’s estimated that hot water uses 25% of your home’s power, so gas can save a lot of money switching.
Commercial Hot Water Heaters
A commercial system normally involves a mix of circulating pumps and conventional high demand hot water systems
Thermostatic Mixing Valves
Thermostatic mixing valves can be installed by any plumber but must be serviced and inspected once a year.
Hot Water Heater Tempering Valves
Tempering valves blend incoming hot and cold water together are set at 65°C to prevent scalding temperatures.
Instant Hot Water Dispenser
A Hot water dispenser produces instant hot or cold water, it's usually an addition to a normal household tap.
If Your Hot Water A concern? CALL US NOW. Our North Wahroonga Hot Water Plumbers Can Find The Solution That Best Serves Your Needs.
0420 102 394Recent Community Projects
I cannot thank the team at Proximity Plumbing and Sydney Relining Company for a quick, affordable pipe repair solution for a previous blocked & broken drain issue. No fuss, no mess, avoided reinstatement costs and completed the same day. It was hassle-free, with interest-free finance available. As promised, this was a" no-dig" solution with a 35-year guarantee.
I have been using Proximity Plumbing as my preferred local plumber for years now, the team are always friendly, they show up on time within 30 minutes and always doing such a great plumbing job, whenever any of my friends are looking for plumbing near me I always refer my trusty local plumbers- Proximity Plumbing, thanks again guys for doing such a great job at annually clearing out my blocked drains.
Proximity Plumbing are our trusted plumbers whenever we encounter any plumbing issues in all the residential and commercial properties that we handle. Its best to have an on-call plumber who can go onsite within 30 minutes. They were able to clean the roof and gutters immediately and also provided permanent solution on the plumbing problem. Thanks to Proximity Plumbing for a smooth and hassle-free agreement.
Our drains were blocked due to tree roots and were apparently damaged by it. Proximity Plumbing has given us one of the best solution that is lifetime guaranteed - Pipe Relining. We were happy how they were able to work hand-in-hand with each other which resulted to a good outcome. All drains were cleared and our pipe was fixed. We will truly get in touch with Proximity Plumbing again in case that we will be having any plumbing issues again.
Our gutters and stormwater pits needed urgent cleaning. We immediately contacted Proximity Plumbing to clean our gutters and stormwater pits. They were very professional and they were able to clean it right away. They definitely deserve a 5-star review since they did a great job. We will get in touch with them again once we encounter any plumbing issue.
Two tradesmen from Proximity Plumbing attended on site after our report of blocked drain. They have confirmed that the kitchen drain was blocked with grease. We are greatly impressed on how they resolved the problem. The job was handled professionally by our partner plumbers. Proximity Plumbing did a great job overall.
We had a burst hot water unit in Maroubra in the middle of the night. Good thing, Proximity Plumbing offers emergency plumbing service in Eastern Suburbs. We immediately contacted them and they were able to report on site in less than 10 minutes. They have diagnosed the issue right away and replaced the broken hot water unit with a new one in the morning. Proximity Plumbing are very efficient and professional plumbers. Definitely a job well don!
Our Recent Work On Hot Water System
Hot Water Replacement
Hot Water Installtion
Hot Water Reapir
Hot water heater repair
Don’t Believe Everything You Read On The
Internet Believe What You Watch Instead-This Is What We Get Up To On A Daily Basis!
Our Latest Plumbing Blogs
Frequently Asked Questions About Hot Water
Hot water is something that we all take for granted and when it is gone it can cause overwhelming concerns. Rest assured when you call proximity plumbing, we get your hot water back on in no time! We also offer from the moment you call our friendly expert advice and solutions to see if it's something minor that doesn't always require a plumber.
If the issue is more complicated such as insufficient hot water, low water pressure or a leak our highly skilled tradesmen will respond to your request and identify the cause of the issue. We aim to ensure minimal downtime and the most cost-effective solution to get hot water again.
Are you also wondering how long until you need to replace your hot water system? Check this link: https://proximityplumbing.com.au/blogs/how-long-until-i-need-to-replace-my-hot-water-system/
If you're searching for Sydney gas hot water service or installation, look no further. Your local Sydney hot water plumber can handle this for you and we can provide the best gas hot water solution to suite your home and requirements.
If you’re aiming for an energy-efficient home.
Gas hot water systems are more energy-efficient as they heat water faster and don’t run as often as electric models. They are typically also smaller units. You can also install a continuous flow hot water system, also known as an Instantaneous or Tankless system. These systems heat water as you need it, without a storage tank. That means you’ll never run out of hot water.
If you want to avoid costly installation. Gas hot water units generally come with more upfront costs. If you currently run an electric unit and are wanting to install a gas unit, know that you will need to invest in a natural gas line installation by a qualified gas fitter. That cost coupled with the new gas system could add up to a more expensive initial outlay. If you want to save money over time. Although gas hot water systems come with more upfront costs, the savings on your energy and water bill will be seen over time. This analysis is based partially on the fact that natural gas is typically less expensive than electricity and you don’t need to worry about off-peak tariffs. Plus, you can talk to our expert team at Proximity Plumbing for advice on what will suit your current home. Feel free to call us today on 0420 102 394 for a free quote. We are pros at installing and repairing hot water systems and will gladly answer your questions. Plus, we guarantee to be on-site within the eastern suburbs in 30 minutes!
Your high-quality hot water unit will usually last 10 years or more, but here are some tips from Proximity Plumbing on how to know when to replace it.
- Age
- Discoloured Water
- Noisy
- Leaks
- Frequent Problems
Don’t wait for your hot water unit to shut down all together. Trust us - if past experiences are anything to go by, it will decide to shut down at the most inconvenient of times.
Read more about the signs it's time to replace your hot water system: https://proximityplumbing.com.au/blogs/signs-that-its-time-to-replace-your-hot-water-system/
Did you know Proximity Plumbing have helped over 5400 + homes get their hot water up & running throughout the last 10 years, we know having hot water is crucial and thankfully we know what's best to recommend thanks to being partners with Reece plumbing.
These heaters can come in both electric and gas, with electric options you can also choose to go with off-peak power to save money on larger models.
Approximately 30 to 45 per cent lower running costs than their electric counterparts.
A solar water heater works just like a battery, storing energy from the sun in the form of hot water, ready for use at a later time
A heat pump uses renewable energy to heat and absorb the heat from the surrounding air and use it to heat your water.
Sizes ranging from 250-400 litres and come in all brands and models for any application.
It's estimated that hot water uses 25% of your home's power, so gas can save a lot of money switching.
A commercial system normally involves a mix of circulating pumps and conventional high demand hot water systems
Thermostatic mixing valves can be installed by any plumber but must be serviced and inspected once a year.
Tempering valves blend incoming hot and cold water together are set at 65°C to prevent scalding temperatures.
A Hot water dispenser produces instant hot or cold water, it's usually an addition to a normal household tap.
Did you know that your home’s hot water accounts for almost a quarter of your energy costs? Over time, that’s a lot of money wrapped up in hot water! So, the choice between which heater system - gas or electric, is a crucial one.
To save time and avoid a ‘panic buy’ it’s best to do some research now and replace your aging system before disaster strikes. Usually, when hot water systems come to the end of their life it’s a dramatic ending. So, the answer to whether a gas or electric hot water heater is best depends on your home, family’s needs, and what you value more.
Read more about gas or electric water system here: https://proximityplumbing.com.au/blogs/gas-vs-electric-hot-water-heater/
You will need to consider the size of the water heater you need in your home. Water heaters with a higher tank capacity or heating capacity will always be more expensive than smaller units. This is true whether you choose an electric system like a heat pump water heater, a solar water heater, or a water heater powered by natural gas.
So we highly recommend consulting with an experienced plumber and discussing how much hot water your home needs. Tanks can vary in size from 251 all the way up to 400L, and tankless, on-demand heaters vary greatly in capacity, too. Choosing the right size will help you save money when installing and operating your water heater.
Proximity Plumbing is a family-run 24/7 maintenance plumbing business based in the eastern suburbs, we specialise in hot water heaters and successfully service and replace for both residential and commercial areas. Feel comfortable calling one of our friendly staff and organising the closest plumber in our team to attend your property as quickly as possible.
We offer unparalleled hot water system installation repairs, and service at competitive prices. We have built an impeccable reputation for providing the highest quality service with our leading industry knowledge and experience within the eastern suburbs.
A solar hot water heater uses solar panels or collectors to absorb the thermal heat from the sun, that then heats water in a storage tank. Solar panels or collectors need to be exposed to direct sunlight, so they ideally need to be installed on a roof.
For a typical household, water heating accounts for about 30 percent of total greenhouse gas emissions and household energy use. Depending on the climate and the model of heater, a solar water heater can provide between 50 to 90 percent of your total hot water requirements.
Know more about different hot water systems here: https://proximityplumbing.com.au/hot-water-repairs/sydney/
Proximity Plumbing prides itself at providing a minimum of three options to tackle a Hot Water system fault. Depending on the source of the Hot Water will determine the appropriate method whether it's repairing the Hot Water leak, upgrading your hot water unit or just a general hot water service.
Using Hot Water detecting equipment is the first crucial step in making your property safe again, and in the long term, attending to Hot Water leaks swiftly means you save money by not paying inflated Hot Water bills due to leaking Hot Water. In some circumstances, we can provide an option which may be an energy-efficient hot water system that suits your budget and meets a high energy star rating.
We are licensed hot water specialists that are licensed to install & service all types of hot water systems, when dealing with us you will have lifetime labour warranty & manufacturers warranty. Proximity Plumbing don't take shortcuts when installing your hot water tank in your home, we ensure everything is to code including supplying a mandatory tempering valve to ensure no one gets burnt from scalding hot water.
The EVO270 has won the 2021, 2020 & 2019 hot water Product Review Award for 3 consecutive years, even after being recognised by Australian customers because of its innovative energy efficiencies and intelligent features.
It has been considered the next evolution in water heating, with advanced energy efficiency technologies and built-in smart features to ensure you're provided with clean, safe, and economical hot water all year round.
The EVO 270 has innovative energy efficiency technology and constructed with smart features to guarantee you're supplied with clean, secure, and affordable warm water throughout the year.
Unlike conventional hot water systems which use TkW of electricity to produce 1kW of warmth, the EVO 270 uses the same 1kW of power and heat pump technologies to create 4kW of warmth — saving you around 75 percent of your hot water prices!
Key Points:
1. Hot water up to 70°C
2. Storage Capacity: 270 litres
3. Locations: Outdoor or Indoor.
Read more about our hot water service: https://proximityplumbing.com.au/hot-water-repairs/sydney/
At Proximity Plumbing, we are experts in helping Sydney Eastern Suburbs locals choose a gas heating solution that will meet the unique needs of their suburb, home design and build type. As. your gas plumbing partner, we can help you understand the benefits of many different types of gas heating.
Natural gas is a good option if you have the connection for it. It can be cheaper than electricity (unless you have solar panels) and because gas rates don't vary through the day, gas hot water systems can heat water as needed. One important consideration is that gas is a fossil fuel, and moves to reduce carbon emissions will probably make gas a less attractive option in the future. While it's currently cheaper than grid electricity, it's nowhere near as cheap as your own solar-generated electricity if you have solar panels.
Learn more about our gas heating service here: https://proximityplumbing.com.au/services/gas-heating/
The average cost of installing a new hot water system in Australia is between $200, and $600. However, this is only the case if you're replacing an existing hot water system with one of the exact same type, and this does not factor the cost of the water heater unit itself into account.
Every household should have a hot water system that is running efficiently and effectively. IF you notice any of the below signs, you know you have a bigger problems:
- Leaks in the tank
- The temperature has changed to cold
- Hot water running out regularly
- Large water bills
Here are the signs that your hot water system needs replacement: https://proximityplumbing.com.au/blogs/signs-that-its-time-to-replace-your-hot-water-system/